Free TV Antenna Direction Finder: See Exactly Where to Point Your Antenna

Imran HossainBy , IEEE Member · Updated November 2026

Enter your address or ZIP code to see every TV tower near you and the best direction to aim your antenna.

TV Antenna Direction FinderUS over-the-air TV · FCC data

Quick answer: Point your TV antenna at the compass bearing of the transmitter towers. Most cities have their towers in one or two spots, so one direction often covers most channels. Use the true bearing with a map, or the "compass" bearing with your phone, because the two can differ by more than 10°.

I built this because most direction finders give you a list of stations and stop there. That leaves the hard part to you: working out one direction that gets the most channels, and what your compass should read.

How to use the TV antenna direction finder

  1. Enter your address or ZIP code, or tap "Use my location". A street address gives the most accurate bearings.
  2. Set your antenna height in Options. Height changes how far you can reach. Leave it at 30 ft for a typical roof.
  3. Read the big number first. That is the direction that covers the most receivable stations.
  4. Check the band. If any station you want is VHF, your antenna must support VHF.
  5. Aim, rescan, fine-tune. Point the antenna, run a channel scan on your TV, then turn it a few degrees at a time to find the best signal.

How to read your results

True NMag Ndeclination

True bearing vs compass bearing

The big number is a true bearing, measured from true north. A phone or hand compass points to magnetic north. The difference is called magnetic declination. We work it out for your exact location with the NOAA World Magnetic Model, and show the compass value next to every station.

N

Aim zone

The orange wedge on the chart is the best direction for your antenna's beam. Change the beamwidth in Options to match your antenna. Long Yagis have narrow beams. Small flat antennas have wide ones.

StrongGoodWeakV. weak

Signal levels

Strong usually works with an indoor antenna. Good works best in the attic or outdoors. Weak needs an outdoor directional antenna. Very weak may not work at all.

7.1What TV showsRF 33UHFReal frequency

Channel vs RF channel

The big channel number is the one your TV shows. The RF channel is the frequency the station really uses. The RF channel decides the band (VHF or UHF), and the band decides which antenna you need.

How to aim a TV antenna, step by step

This is the order I recommend. With a helper, it usually takes 15 minutes or less.

  1. Mount the antenna first, then aim it. Put it as high as you can, clear of metal roofs, gutters and trees.
  2. Set the rough direction. Stand behind the antenna, open the compass on your phone, and use the compass bearing from the results. Or use the Live compass button in the tool.
  3. Run a channel scan. Check how many channels you get.
  4. Fine-tune with the signal meter. Most TVs have a signal strength screen in the antenna or channel menu. Turn the antenna about 5° at a time and wait a few seconds after each move.
  5. Lock it and rescan. Tighten the mast, seal outdoor connectors, and run one last scan.

One small tip: don't chase the strongest channel. Aim for the direction where your weakest wanted channel still comes in. The strong ones will almost always follow.

Which TV antenna do you need?

Ignore the "200-mile range" on the box. No home TV antenna does that, because the curve of the earth hides the tower long before. What really matters is your distance, your signal level and the band. Match your results to this table.

Your resultsAntenna typeWhere to mountNotes
Mostly Strong, under about 25 milesFlat indoor antenna or small bow tieWindow or high on a wall facing the towersCheapest option. Try several spots in the room.
Good, 25–45 milesMedium Yagi or log periodicAttic or roofAttic loses some signal through the roof, more with foil insulation.
Weak, 45–70 milesLarge directional Yagi plus a low-noise preampRoof, as high as possiblePut the preamp at the mast, not at the TV.
Towers in two or more directionsMulti-directional antenna, a rotator, or two antennas with a joinerRoofThe tool tells you when this applies.
Any VHF station in your listAntenna rated for VHF-High (and VHF-Low if needed)Same as aboveMany small "HDTV" antennas are UHF-only. See the VHF antenna calculator.

Building your own? The UHF antenna calculator and the Yagi calculator give element lengths for any TV channel. The driven element of most TV Yagis is a folded dipole.

Still getting a weak or breaking-up picture?

Before you buy a bigger antenna, check the cheap stuff first. Old coax and extra splitters cause more problems than most people think.

  • Hills and buildings. This tool does not model terrain. A hill between you and the tower can block a station that looks "Good". Raising the antenna a few feet sometimes fixes it.
  • Long or old coax. Every foot of cable loses signal, more at higher channels. Check yours with the coax cable loss calculator. Use RG-6, not old RG-59.
  • Splitters. Each 2-way split costs about 3.5 dB per output. Feeding four TVs can cost as much as a long cable run.
  • Cell tower interference. Mobile networks use the 600 MHz band, just above TV channel 36. If you live near a cell tower, an LTE/5G filter can help.
  • Amplifier overload. Too much gain near strong towers can make reception worse, not better. Only add a preamp when your stations are weak.
  • Reflections (multipath). Signals bouncing off buildings can cancel each other. A more directional antenna usually helps.

How this tool works

The tool uses public station data from the FCC TV Query database: each station's transmitter location, RF channel, power (ERP) and antenna height. From your location it calculates the great-circle bearing and distance to every tower.

bearing = atan2( sin Δλ · cos φ₂ , cos φ₁ · sin φ₂ − sin φ₁ · cos φ₂ · cos Δλ )

Magnetic declination comes from the NOAA World Magnetic Model 2025, calculated in your browser for today's date. The compass bearing is the true bearing minus the declination.

I kept the signal model simple on purpose, so treat it as a rough guide. It starts from free-space field strength for the station's power and distance, subtracts an average loss for clutter, and adds a penalty beyond the radio horizon. It then compares the result with the FCC's minimum field strength for digital TV (47 CFR § 73.622): 28 dBµV/m for channels 2–6, 36 for channels 7–13 and 41 for UHF. It does not know about hills or buildings. If a station shows "Good" but you get nothing, terrain is the usual reason.

The best-direction finder checks every degree from 0° to 359° and picks the bearing that covers the most receivable stations inside your antenna's beam.

Before you blame the antenna

If a channel comes in fine during the day but breaks up in the evening, the antenna is often not the problem. On warm, still evenings, signals from distant stations on the same channel can travel much farther than usual and interfere with your local one. It usually clears by morning.

When your towers sit 30° to 40° apart, I'd pick a slightly wider antenna and aim between them rather than a long, narrow Yagi. A narrow beam split down the middle tends to leave both groups weak. And if you have the choice, raising the antenna from the attic to the roof often helps more than buying a bigger one.

TV antenna direction FAQ

Which direction should I point my TV antenna?

Point it toward the transmitter towers of the stations you want. Enter your address in the tool above to see the exact bearing. If your towers are in one area, one direction covers most channels. If they are spread out, use a multi-directional antenna or a rotator.

Should I use true north or magnetic north?

Use the true bearing when you aim with a map or satellite view. Use the compass bearing when you aim with a phone or hand compass. The difference is magnetic declination, which is more than 10° in parts of the US.

How do I know if a station is VHF or UHF?

Look at the RF channel, not the channel number your TV shows. RF channels 2–6 are VHF-Low, 7–13 are VHF-High, and 14–36 are UHF. The tool labels each station for you.

Does the antenna need to point exactly at the tower?

Not exactly. Most TV antennas have a beam 40° to 90° wide. Aim close to the bearing, then fine-tune a few degrees at a time while you watch the signal meter.

Why do I get some channels but not others?

Stations differ in power, distance, band and direction. A channel can also be blocked by terrain or need a VHF-capable antenna. Check that station's direction and band in your results.

Will an amplifier help?

A preamp helps when signals are weak or the coax run is long. It does not help when the antenna is pointed the wrong way, and it can hurt reception near strong towers.

Does this work outside the US?

The station list covers US over-the-air TV. Bearings and declination work anywhere, so you can enter coordinates in Options if you know your tower's location.

Related tools

Sources

  • FCC TV Query and FCC DTV Reception Maps: station locations, channels, power and antenna height.
  • FCC consumer guide: Antennas and Digital Television (PDF).
  • NOAA / BGS World Magnetic Model 2025: magnetic declination.
  • 47 CFR § 73.622(e): minimum DTV field strength by band.
Imran Hossain, antenna engineer

Written by , B.Sc. in Electrical & Electronic Engineering, IEEE Member.

Imran designs and tests antennas and has published antenna research on IEEE Xplore. He built this tool and checks its bearings and declination against NOAA and FCC reference data.

Scroll to Top