Coax Cable Loss Calculator: RG-58, RG-6, LMR-400 & More

Coax Cable Loss Calculator: See How Much Signal Your Cable Eats

Imran HossainBy , IEEE Member · Updated November 2026

Pick a cable, enter the length and frequency, and see what reaches the antenna.

Connectors, SWR and splitters

Good N or F connectors lose about 0.05–0.15 dB each. Cheap adapters can lose more.

Total loss
–
Into cable–
At antenna–
Per 100 ft–
Per 100 m–
Lost as heat–
SWR at radio–
Velocity factor–
Electrical length–

Loss across the spectrum

Loss for your length, from 1 MHz to 6 GHz.

Move over the chart to read values.

Compare every cable for this run

Same length and frequency. Tap a row to switch. Tick up to 3 to plot.

CableLossOutMax runPlot

Short answer: coax loss depends on three things: the cable type, its length, and the frequency. A 100 ft run of RG-58 at 146 MHz loses about 4.7 dB, so only a third of your power reaches the antenna. The same run in LMR-400 loses about 1.5 dB, and 70% gets through. Every 3 dB of loss cuts your power in half.

The numbers come straight from manufacturer datasheets: Belden for the RG cables, Times Microwave for LMR, and CommScope for Heliax. Between the frequencies a datasheet lists, the calculator interpolates. It never guesses past the datasheet without telling you.

Coax loss per 100 feet, cable by cable

This is the table most people come here for. Values are typical loss in dB per 100 ft with a matched load. For dB per 100 m, multiply by 3.28.

Cable14 MHz
HF
146 MHz
2 m
440 MHz
70 cm
900 MHz2.4 GHz
Wi-Fi
5.8 GHz
50 Ω: radio, Wi-Fi, cellular
RG-581.34.78.913.7——
RG-8X1.13.87.010.7——
LMR-1951.44.47.711.118.629.9
LMR-2400.93.05.27.612.620.4
RG-2130.72.34.47.614.9—
Belden 9913F70.71.83.24.78.5—
LMR-4000.51.52.73.96.610.8
LMR-6000.31.01.72.54.37.3
1/2" Heliax LDF4-50A0.20.81.42.13.66.0
7/8" Heliax LDF5-50A0.10.40.81.22.1—
75 Ω: TV, satellite, cable
RG-591.02.84.97.212.420.6
RG-60.82.44.16.010.217.3
RG-110.51.52.63.96.711.3

"—" means the maker does not list that frequency. Don't count on the cable there.

Bar chart comparing coax loss per 100 feet for RG-58, RG-8X, LMR-240, RG-213, LMR-400 and LMR-600 at 150 MHz, 450 MHz, 900 MHz and 2.4 GHz
Same cables, four frequencies. Loss climbs fast with frequency, and thin cable climbs fastest.

Which coax for which job

There is no single "best" cable. There is a cable that is good enough for your run. These picks balance loss, price and cable size for a typical home run.

Over-the-air TVUHF, around 600 MHz

Use RG-6 with a quad shield if you live near strong signals. 100 ft loses about 4.8 dB. For runs past 150 ft, or weak stations, switch to RG-11 or put a preamp at the antenna. Use the TV antenna direction finder to check how strong your stations are.

RG-6RG-11 for long runs

Satellite dishLNB output, 950–2150 MHz

Satellite needs RG-6 with solid copper center (not copper-clad steel), because the receiver sends power up the cable. 100 ft at 2150 MHz loses about 9.6 dB. That is normal. Most receivers handle it.

RG-6solid copper core

HF ham radio3.5–30 MHz

Loss is low at HF, so cable choice matters less. 100 ft of RG-8X at 14 MHz loses about 1.1 dB. RG-213 cuts that to 0.7 dB and handles more power. For a dipole, see the dipole calculator.

RG-8XRG-213 for high power

2 m / 70 cm base146 and 440 MHz

Here RG-58 starts to hurt. 100 ft of LMR-400 loses 1.5 dB on 2 m and 2.7 dB on 70 cm. On a repeater or a tall tower, go to LMR-600 or 1/2" Heliax.

LMR-400LMR-600 above 100 ft

Wi-Fi, LTE, 5G0.7–6 GHz

Keep the cable short. Even LMR-400 loses 3.3 dB on 50 ft at 2.4 GHz. Mount the radio near the antenna if you can, and run Ethernet instead of coax.

LMR-400keep it under 50 ft

GPS antenna1575 MHz

Active GPS antennas have an amplifier, so they can handle 3–5 dB of cable loss. LMR-195 is a good fit up to about 30 ft. For longer runs, use LMR-240 or LMR-400.

LMR-195LMR-240 past 30 ft

Why coax loses signal

Coax is two metal conductors with an insulator between them. RF energy travels in that insulator. Some of it turns into heat along the way. That heat comes from two places.

Coax cable cross-section showing jacket, braid shield, foil, foam dielectric and center conductor, with conductor loss and dielectric loss explained
Conductor loss rises with the square root of frequency. Dielectric loss rises in a straight line with frequency.

Conductor loss. At radio frequencies, current flows only on the surface of the metal. This is called skin effect. A thin center wire has little surface, so it heats more. That is why fat cable loses less.

Dielectric loss. The plastic between the conductors absorbs a bit of energy on every cycle. Solid polyethylene (RG-58, RG-213) absorbs more than foam (LMR, RG-6). This part takes over at GHz frequencies.

Both grow with frequency. So a cable that is fine on 14 MHz can be useless on 2.4 GHz.

What a few dB of loss really means

Decibels are easy to read wrong. Here is what each step does to your power.

1 dB79% left
2 dB63% left
3 dB50% left
6 dB25% left
10 dB10% left
20 dB1% left

On transmit, lost power just warms the cable. On receive, it is worse. Cable loss before the first amplifier adds straight to your noise figure. So 3 dB of cable loss in front of a receiver makes weak signals 3 dB harder to hear. That is why TV and satellite installers put the amplifier at the antenna, not at the TV. Use the dBm to watts converter if you need to change units.

High SWR makes cable loss worse

When the antenna is not matched, part of the power bounces back down the cable. It passes through the cable again, so it loses more on the way. The table above assumes a perfect match. The calculator adds this extra loss when you enter your SWR.

Chart of extra coax loss caused by SWR from 1:1 to 7:1 for cables with 1 dB, 3 dB and 6 dB matched loss
Below 2:1 the extra loss is a few tenths of a dB. Above 3:1 on a lossy cable, it adds up fast.

Loss also hides a bad antenna. Your radio sees a lower SWR than the antenna really has, because the reflected power is weakened on the way back. A long run of thin cable can make a broken antenna look fine. The calculator shows this as "SWR at radio". Check your match with the SWR calculator.

The math this calculator uses

You can check every number by hand. These are the formulas behind the result.

Cable loss (LMR)A(dB/100 ft) = k1·√f + k2·f (f in MHz)
Cable loss (RG, Heliax)log-log interpolation between datasheet points
Loss for your runML = A × length(ft) / 100
ReflectionΓ = (SWR − 1) / (SWR + 1), a = 10^(ML/10)
Total loss with SWRTL = 10·log10[(a² − Γ²) / (a·(1 − Γ²))]
SWR at the radioΓin = Γ / a, SWR = (1 + Γin) / (1 − Γin)
Power outPout = Pin × 10^(−total dB / 10)

The total adds connector and splitter loss on top. Times Microwave publishes k1 and k2 for each LMR cable. For RG and Heliax cables, the calculator uses the maker's table directly, so results match the datasheet at every listed frequency. Electrical length uses the velocity factor: one wavelength in the cable is 300 / f(MHz) × VF meters.

Before you buy thicker cable

Cheaper ways to cut loss

  • Shorten the run. Move the radio, not the antenna.
  • Put a preamp at the antenna for receive-only setups.
  • Use one long piece, not several joined with barrels.
  • Seal outdoor connectors with tape. Water inside coax raises loss for good.

Things that waste signal

  • Cheap adapters stacked on top of each other.
  • A splitter with more ports than you need. Each 2-way split costs 3.5 dB.
  • RG-58 on anything above 400 MHz past a few feet.
  • Kinks and tight bends that crush the foam.

Coax loss questions

How much signal does coax lose per 100 feet?

It depends on the cable and frequency. At 146 MHz, RG-58 loses about 4.7 dB per 100 ft, RG-8X 3.8 dB, RG-213 2.3 dB and LMR-400 1.5 dB. At 600 MHz (UHF TV), RG-6 loses about 4.8 dB per 100 ft.

Is RG-6 or RG-59 better for a TV antenna?

RG-6. It has a thicker center conductor and loses about 20% less than RG-59 at UHF TV frequencies. RG-59 is fine only for short jumpers.

How much loss is too much?

For transmit, try to keep it under 3 dB, which means half your power reaches the antenna. For receive, less is better, unless you have a preamp at the antenna. Then 5–10 dB of cable loss is usually fine.

Can I use 75 Ω TV coax for a 50 Ω radio?

On HF, yes for receive and low power. The mismatch gives about 1.5:1 SWR, which costs little. On VHF and above, use real 50 Ω cable.

Does coax loss change with temperature?

A little. Datasheet values are at 20–25 °C. Loss rises slowly as the cable gets hotter, by roughly 1% for each 5 °C. That matters only on long, sunny, high-power runs.

Does a longer cable lower SWR?

It lowers the SWR your radio reads, but not the real SWR at the antenna. The cable eats part of the reflected power, so the meter looks better than the antenna really is.

More tools for your antenna setup

Sources: attenuation data from the Belden 8240 (RG-58) datasheet and the CommScope LDF4-50A datasheet, plus matching Belden, Times Microwave and CommScope datasheets for the other cables.

Imran Hossain, antenna engineer

Written by , B.Sc. in Electrical & Electronic Engineering, IEEE Member.

Imran designs and tests antennas and has published antenna research on IEEE Xplore. He built this calculator from manufacturer datasheets and checked every cable against its published loss table.

Scroll to Top